just created new v3.5 ubcd4windovs based on sp2version. works very well on one pc and getting blank screen on another. after initial load screen and starting windows xp screen the screen gets blank. i suspect compatibility or driver problem. may be it's known problem.
my system:
motherboard
asustek model m2n-e
chipset nvidia
bios pnoenix, version asus m2n-e acpi bios rev. 0802
graphic interface pci-express
cpu amd athlon 64x2 3800+
thanks a lot!
yoryb
Page 1 of 1
Blank Screen v3.5 boots on one pc and doesn't on another
#2
Posted 24 September 2009 - 09:34 PM
When you see "Press F6 to load additional drivers", press F7 instead.
If you're afraid of taking any chances then the chances are great that you will never learn anything
Multiboot Plugins - UBUSB (Ultimate Boot USB) - EzPcFix - RootKitty - Network Configuration Utility - UnIsoFS - A Small Linux Distro - SELogger - HashME - WSock - My Paypal
Multiboot Plugins - UBUSB (Ultimate Boot USB) - EzPcFix - RootKitty - Network Configuration Utility - UnIsoFS - A Small Linux Distro - SELogger - HashME - WSock - My Paypal
#4
Posted 25 September 2009 - 03:07 PM
Hi yorby
I saw something similar under real Windows XP on a old PC recently when I switched the base unit on before the LCD screen.
Do you have access to a CRT screen ?
If you did not see 'Press F6 to load additional drivers' maybe the screen blanked before the message was displayed
or you blinked at the wrong moment
You could try a simple BartPE disk to see if any extra drivers or registry entries in ubcd4win are causing a problem
chipset by nvidia sometimes cause problems with SATA /AHCI / Raid disks under UBCD4WIN
you can boot up but not see the hard disk
regards
Mike Barnes
I saw something similar under real Windows XP on a old PC recently when I switched the base unit on before the LCD screen.
Do you have access to a CRT screen ?
If you did not see 'Press F6 to load additional drivers' maybe the screen blanked before the message was displayed
or you blinked at the wrong moment
You could try a simple BartPE disk to see if any extra drivers or registry entries in ubcd4win are causing a problem
chipset by nvidia sometimes cause problems with SATA /AHCI / Raid disks under UBCD4WIN
you can boot up but not see the hard disk
regards
Mike Barnes
This post has been edited by mbarnes: 25 September 2009 - 03:08 PM
#5
Posted 27 September 2009 - 01:11 AM
mbarnes, on 25 September 2009 - 12:07 PM, said:
Hi yorby
I saw something similar under real Windows XP on a old PC recently when I switched the base unit on before the LCD screen.
Do you have access to a CRT screen ?
If you did not see 'Press F6 to load additional drivers' maybe the screen blanked before the message was displayed
or you blinked at the wrong moment
You could try a simple BartPE disk to see if any extra drivers or registry entries in ubcd4win are causing a problem
chipset by nvidia sometimes cause problems with SATA /AHCI / Raid disks under UBCD4WIN
you can boot up but not see the hard disk
regards
Mike Barnes
I saw something similar under real Windows XP on a old PC recently when I switched the base unit on before the LCD screen.
Do you have access to a CRT screen ?
If you did not see 'Press F6 to load additional drivers' maybe the screen blanked before the message was displayed
or you blinked at the wrong moment
You could try a simple BartPE disk to see if any extra drivers or registry entries in ubcd4win are causing a problem
chipset by nvidia sometimes cause problems with SATA /AHCI / Raid disks under UBCD4WIN
you can boot up but not see the hard disk
regards
Mike Barnes
Thanks for help!
The problem is the monitor-lcd tv with hdmi input. video card is ATI 1600 for which I've installed driver pack in my ubcd4win.
With a regular lcd monitor with dvi input the ubcd4win works just fine.
I have not seen anybody at this forum with this type of problem.
probably ubcd4win is not ready yet for pc with such configuration.
Thanks a lot for help!
yoryb.
Page 1 of 1