....There is no NIC card displayed in the pulldown....reinstalled from website, got the same thing....anybody have a clue here....?
RE: SetRes does not work....I have a Dell / Extreme Intel Graphics #1...
Any suggestion....
Full Version: ShowTraffic / SetRes neither work....
Ok, I'm working on trying to figure out why your NIC won't work....can't remember if I included the drivers for that too or not. Actually I couldn't have since you installed it to the SCSIAdapter folder. Gotta dig up the files and find the NIC driver for that.
Now for the graphics, does the screen display at all?? We have had issues in the past with onboard graphics from Intel not wanting to work with the project. So I just want to know if you do boot into it and can access everything. I think there may be an issue with the SetRes, but haven't had the time to check into it. Since very few people have mentioned problems with it I didn't think it was that important to look into yet.
Can you access your harddrive now? Does everything else seem to work for you??
Actually I'm going to need you to provide me another link from Dell for the NIC driver, the one in the previous post only points to the SATA driver. Since I do not have a tag number or any other information, Dell will not allow me to search.
Now for the graphics, does the screen display at all?? We have had issues in the past with onboard graphics from Intel not wanting to work with the project. So I just want to know if you do boot into it and can access everything. I think there may be an issue with the SetRes, but haven't had the time to check into it. Since very few people have mentioned problems with it I didn't think it was that important to look into yet.
Can you access your harddrive now? Does everything else seem to work for you??
Actually I'm going to need you to provide me another link from Dell for the NIC driver, the one in the previous post only points to the SATA driver. Since I do not have a tag number or any other information, Dell will not allow me to search.
Ok, I actually have my broadcom drivers installed in the pe builder313 folder in the drivers\net\winxpbcom directory...I MANUALLY installed these drivers when I was working with the "U-DO-IT" Bart PE environment, and actually right now, the initial ubcd windows detect NIC and install applet works FINE....
As for SET RES, the graphics come up FINE at a default 1024 x 768, it's just that SET RES cannot modify anything even ran it manually from command line...also I seem to remember that again, the original BART PE U-DO-IT environment had resoution menuing that DID work just fine.....
OK then...........
Matt / Los Angeles
As for SET RES, the graphics come up FINE at a default 1024 x 768, it's just that SET RES cannot modify anything even ran it manually from command line...also I seem to remember that again, the original BART PE U-DO-IT environment had resoution menuing that DID work just fine.....
OK then...........
Matt / Los Angeles
Ok, so everything is fine now?? Everything is working for you?
FYI... We should have all Broadcom NIC drivers in the upcoming driver release. 
Oh no. Setres does not work, and showtraffic does not offer any NIC cards to select. EVen when I download showtraffic off the website, that doesn't work either.....
If Showtraffic doesn't work in your normal XP environment then I highly doubt it would work in the UBCD4Win environment.
As for Setres, I think you are just going to be stuck with the default resolution (which is a good resolution) due to the fact that you have on-board video and this CD has been known to be flaky with such devices. I'm sorry but we haven't found a fix for that yet (that I know of). :-\
As for Setres, I think you are just going to be stuck with the default resolution (which is a good resolution) due to the fact that you have on-board video and this CD has been known to be flaky with such devices. I'm sorry but we haven't found a fix for that yet (that I know of). :-\
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please click here.